Brady 300X-PLUS Uživatelská příručka Strana 139
- Strana / 208
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
129
Routine Maintenance
Clean the Sensors
1/11/07 X-Plus II User Guide 14068L-001 Rev. A
1
Label-available sensors
2
Ribbon sensor
1
2
- Bradyprinter™ X-Plus II 1
- FCC Declaration of Conformity 3
- Compliance Information 4
- CE Declaration of Conformity 5
- Contents 10
- About This Document 11
- Who Should Use This Document 12
- Contacts 13
- Bubbledot ICG font 14
- SETUP/EXIT button 15
- CALIBRATE button 15
- Document Conventions 16
- Introduction 17
- External View 18
- Printer Components 19
- Control Panel 20
- Control Panel LCD 21
- Control Panel Buttons 21
- Appearance 22
- Printer Setup 25
- Before You Begin 26
- Handling the Printer 27
- Select a Site for the Printer 28
- Connector Locations 29
- Types of Connections 30
- Data Cable Requirements 33
- 4. Turn on (I) the printer 34
- Power Cord Specifications 35
- Types of Media 36
- Ribbon Overview 38
- Adhesive Test 39
- Ribbon Scratch Test 39
- Operations 41
- Prepare the Media for Loading 42
- If… Then… 43
- Load Media in Tear-Off Mode 45
- 1) all the way out 47
- Load Ribbon 51
- 1) and under the 53
- Remove Used Ribbon 56
- Calibrate the Printer 58
- SENSOR PROFILE 59
- MEDIA AND RIBBON 59
- CALIBRATE 59
- Adjust Media Sensors 60
- Lower Media Sensor 62
- Toggle Position Adjustment 63
- Printhead Pressure Adjustment 64
- Setup Mode 68
- Exit Setup Mode 69
- Default Password Value 70
- LIST SETUP 71
- LIST NETWORK 72
- DARKNESS +04.0 74
- - + 74
- PRINT SPEED 74
- 2 IPS + 74
- TEAR OFF +000 75
- PRINT MODE 75
- -TEAR-OFF + 75
- To change the value shown: 76
- Parameter 76
- PRINT WIDTH 77
- - MM + 77
- MAXIMUM LENGTH 78
- 39.0IN 988MM 78
- To reset the media counter: 80
- To reset the ribbon counter: 80
- To format a memory card: 84
- To initialize Flash memory: 85
- PRINT 86
- Action/Explanation 88
- LEFT POSITION 93
- - ±0000 + 93
- HEAD TEST COUNT 94
- - 0000 + 94
- HEAD RESISTOR 95
- - 0500 OHMS + 95
- VERIFIER PORT 95
- APPLICATOR PORT 96
- - OFF + 96
- START PRINT SIG 96
- - PULSE MODE + 96
- To skip these parameters: 97
- - ENGLISH + 99
- Configuration 100
- Control Panel Parameters 100
- Print Modes 101
- PRINT MODE 102
- Load Media in Peel-Off Mode 103
- 1) counter-clockwise 104
- RIBBON OUT error 105
- 1), under the 106
- Print Modes and Options 107
- Load Media in Cutter Mode 110
- Install the Rewind Plate 129
- If... Then 130
- Pull out the spindle hook 131
- Routine Maintenance 133
- CLEAN HEAD NOW appears 134
- HEAD NOW 135
- CLEAN HEAD NOW 135
- Clean the Sensors 138
- Label-available sensors 139
- Ribbon sensor 139
- Clean the Snap Plate 141
- Clean the Cutter 143
- Troubleshooting 147
- Troubleshooting Checklists 148
- ERROR CONDITION 149
- RIBBON OUT 149
- LCD Display/ 150
- Printer Condition 150
- HEAD COLD 151
- DEFRAGMENTING 151
- CUTTER JAM 152
- OUT OF MEMORY 152
- (function) 152
- Print Quality Problems 153
- Note • A vertical drift of 155
- Calibration Problems 156
- NONE. See 157
- Ribbon Problems 158
- LANGUAGE 159
- SAVE CHANGES in the 159
- Printer Diagnostics 161
- CANCEL Self Test 162
- PAUSE Self Test 163
- FEED Self Test 164
- Print Quality Description 166
- FEED and PAUSE Self Test 168
- Sensor Profile 170
- Data Ports 171
- Parallel Data Port 172
- 36-Pin Connectors 173
- Serial Data Port 174
- Pin Configuration 175
- RS-232 Interface Connections 176
- Modem Connection 177
- Applicator Signals 178
- Caution • Replace 180
- Specifications 185
- Features 186
- Bar Codes 187
- Agency Approvals 188
- General Specifications 189
- Print Specifications by Model 190
- Ribbon Specifications 191
- Media Specifications 192
- BP-360X-Plus II Printers 193
- Glossary 195
- Cutter Jam message, 142 200
- HEAD COLD message, 141 201
- HEAD TOO HOT message, 140 201
- OUT OF MEMORY message, 142 202
- PAPER OUT message, 140 202
- RIBBON IN message, 140 203
- RIBBON OUT message, 139 203
- © 2007 Brady Corp 208
Související produkty a manuály pro Tiskárny štítků Brady 300X-PLUS
Tiskárny štítků Brady MINIMARK Manuál s instrukcemi
(81 stránky)
(81 stránky)
Tiskárny štítků Brady IDXPERT Uživatelský manuál
(40 stránky)
(40 stránky)
(56 stránky)
Tiskárny štítků Brady Wraptor Uživatelský manuál
(72 stránky)
(72 stránky)
Tiskárny štítků Brady BMP 51 Uživatelský manuál
(22 stránky)
(22 stránky)
Tiskárny štítků Brady PAM 3000 Návod k obsluze
(87 stránky)
(87 stránky)
Tiskárny štítků Brady BMP71 Manuál s instrukcemi
(25 stránky)
(25 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce